Skip to main content

No Pilot required

Unmanned Aircraft..


The MQ-4C Triton Unmanned Aircraft System (UAS) arrived at Naval Air Station Patuxent River Sept. 18 after completing its inaugural cross-country ferry flight, bringing the Navy closer to delivering this new capability to the fleet.

This flight marked the transition from initial flight test, which established basic safety of flight, to testing that will demonstrate Triton's capability to perform operational missions in the maritime domain.

"Today we brought Triton home to the center of research, development, test and evaluation for naval aviation," said Rear Adm. Mat Winter, who oversees the Program Executive Office for Unmanned Aviation and Strike Weapons (PEO (U&W)) at NAVAIR. "The testing performed here over the next few years is critical to delivering a capability that will provide our warfighter an unparalleled awareness of the maritime environment in locations across the globe."

Winter, along with the flight crew and members from the Triton's Persistent Maritime Unmanned Systems Program Office Office (PMA-262), witnessed the historic landing at 7:53 a.m. During the approximately 11-hour 3,290 nautical mile flight originating from Northrop Grumman's Palmdale, California, facility, the Triton flew along the southern U.S. border, the Gulf of Mexico and across Florida via an approved instrument route. Operators navigated the aircraft up the Atlantic Coast and Chesapeake Bay at altitudes in excess of 50,000 feet to ensure there were no conflicts with civilian air traffic.

"The coordination to bring the Navy's largest unmanned asset across the country was significant and involved many organizations," said Capt. Jim Hoke, PMA-262's program manager. "This phenomenal team executed the system's longest flight to date exactly as planned."

Hoke said this perfect execution was no surprise to him since the system has exceeded performance standards during the course of the last year. Triton has completed 15 test flights prior to today's ferry flight, demonstrating its ability to operate at various speeds and altitudes.

PMA-262 has scheduled Triton operations to start at Pax River within the next several weeks. The Triton integrated test team will conduct further envelope expansion, sensor, communications and interoperability testing.

These are just a few of the many robust tests we will conduct over the next three years, said Mike McDaniel, lead flight test director. Three Triton test vehicles will fly approximately 2,000 hours before achieving initial operational capability in 2017......source: US navy

Comments

Popular posts from this blog

RC plane... Part 2

Continue from part 1... We seen that RC plane is powered by engine or electric motor. We can control that speed using servo motor by radio transmitter. Additional battery is used to supply power to servo motor. There is main 3 control surface as we know which is aileron, elevator and rudder. Aileron is placed on wings while elevator and rudder are placed on horizontal and vertical stabilizer respectively. So that there is 3 servo motor used for controlling this surface for engine powered plane.

RC plane.... Part 1

It is aircraft same as commercial and military aircraft. But RC plane has very small scale compare to actual plane. RC is stand for remote control. So main difference is that RC plane is controlled by remote while actual plane have hydraulic control as we know. RC plane is used to study about flight behavior of actual aircraft so that we can modified in actual plane according to flight. RC plane requires some component like small scale fuselage, power source, battery, radio, propeller,etc. There is mainly 2 type power source used in RC plane, electric powered and engine powered. For electric powered RC plane, brushless motor is used according to requirement. While for engine powered RC plane we can use gasoline engine or diesel engine. Speed of engine or motor is controlled using radio transmitter... ..Continue in part 2.

Aircraft parts

basic parts of fixed Wing Aircraft... Fuselage Wings Vertical stabilizer Horizontal stabilizer Engine Landing gears Fuselage  The fuselage is an aircraft's main body section which contains all other parts like wings, stabilizers, landing gears, passengers,etc. Fuselage is manufactured from material which sustain all parts together. there are many types of fuselage like monocoque, semi monocoque and box struss type. Wings Wings are used for flight by an aircraft to create lift in air. The wings are made with aerofoil cross section. That aerofoil generates a lift when we move it through air.There are two integral parts of wing which are AILERON and  FLAPS. Aileron Basically aileron is used to get rolling movement for aircraft. they are hinged control surfaces attached to the tailing edge of the wing of a fixed wing aircraft. Two ailerons are typically interconnected so that one goes down when the other goes up, the down going aileron increase the lift on